How to Perfect Your Riding Position & Technique

By Ed Pavelka of www.RoadBikeRider.com

Cycling is full of prodigious numbers—the distances ridden, the calories consumed, the tires trashed. Another statistic that can seem astounding is the number of pedal strokes made.

Let’s suppose it takes you six hours to ride a century and you pedal at the rate of 90 rpm throughout. As you cross the finish line, you will be making pedal stroke number 64,800.

Whoa, that’s a lot! But it barely registers on the scale of what happens during a full season. For example, during the year in which I had my biggest mileage total, I figure that I got there by pushing the pedals around approximately 13,340,000 times.

Can you say, repetitive use injury? You can see why cyclists are good candidates, especially if we aren’t pedaling from a nearly perfect position.

Your body and bike must fit together and work together in near-perfect harmony for you to be efficient, comfortable, and injury-free. The more you ride, the more essential this is. If even one thing is out of whack, it’s a good bet that it will cause a problem during thousands of pedal strokes.

Fortunately, it isn’t difficult to arrive at an excellent riding position. But it does take time and attention. You need to be careful with your initial bike set-up, then conscientiously stay aware of your body and the need for occasional refinements. As time goes by, your position will stabilize and you’ll be riding in a smooth groove.

The following guidelines come from my experience and the advice of various experts. One is Andy Pruitt, Ed.D., the director of Colorado’s Boulder Center for Sports Medicine. Andy has probably solved more position problems than anyone during his years of work with elite cyclists.

As you work on your riding position, always remember Pruitt Rule No. 1:

“Adjust your bike to fit your body. Don’t force your body to fit the bike.”

· Frame: Measure your inseam from crotch to floor with bare feet 6 inches apart, then multiply by 0.68. The answer is a good approximation of your road frame size, measured along the seat tube from the center of the crank axle to the center of the top tube. As a double check, this should produce 4 to 5 inches of exposed seatpost when your saddle height is correct. When the crankarms are horizontal, the top tube should be right between your knees when you squeeze them together.

· Arms: Keep your elbows bent and relaxed to absorb shock and prevent veering when you hit a bump or brush another rider. Hold arms in line with your body, not splayed to the side, to be more compact and aerodynamic.

· Upper Body/Shoulders: Don’t be rigid, but do be fairly still. Imagine the energy wasted by rocking side to side with every pedal stroke on a 25-mile ride. Save it for pedaling. Also, beware of creeping forward on the saddle and hunching your shoulders. There’s a tendency to do this when pushing for more speed. Shift to a higher gear and stand periodically to prevent stiffness in your hips and back.

· Head and Neck: Resist the temptation to put your head down when you’re going hard or getting tired. It takes just a second for something dangerous to pop out of nowhere. Occasionally tilt your head to one side and the other instead of holding it dead center. Change your hand location to reposition your upper body and give your neck a new angle.

· Hands: Prevent finger numbness by moving your hands frequently. Grip the bar firmly enough to keep hands from bouncing off on unexpected bumps, but not so tightly that it tenses your arms. For the same safety reason, keep your thumbs wrapped around the bar instead of resting on top. Move to the drops for descents or high-speed riding, and the brake lever hoods for relaxed cruising. On long climbs, grip the top of the bar to sit upright and open your chest for easier breathing. When standing, hold the lever hoods lightly and sway the bike side to side in synch with your pedal strokes, directly driving each pedal with your body weight.

· Handlebar: Bar width should equal shoulder width to open your chest for better breathing. A bit too wide is better than too narrow. Make sure the hooks are large enough for your hands. Modified “anatomic” curves may feel more comfortable to your palms. Position the bottom, flat portion of the bar horizontal or pointed slightly down toward the rear brake.

· Brake Levers: Move them around the curve of the bar to give you the best compromise between holding the hoods and braking when your hands are in the hooks. Most riders do best if the lever tips touch a straightedge extended forward from under the flat, bottom portion of the bar. The levers don’t have to be positioned symmetrically—remember Andy Pruitt’s rule. If your reach is more comfortable with one lever closer to you than the other, put ‘em that way.